Approx. Rs 710 / Piece
These are also called as gap gauges and they are manufactured in steel as well as tungsten carbide.
Gap Gauges are made as per relevant IS Standard blank design and tolerances.
Single ended progressive type
They are most popular snap gauge types owing to its fast gauging method. The front portion of the gauge is the GO member. As the gauge slides into the work-piece it reaches the NOGO member area where it (ideally) stops sliding.
They have dedicated GO and NOGO sides. The gauge has to be inserted in each side to know if it has reached the limit. Although it is a comparatively slow method of gauging it is more reliable and allows more gauging area thereby lower wear and higher gauge life.
Adjustable frame type
They offer the flexibility of building up your own gauge in any size. It is used mostly where the number of components to be inspected is less but the variety of sizes to be inspected is more.
Split type and gauges
0.5 mm. to 4 mm. in Split type design.
4 mm. to 160 mm. in Single ended progressive type or double ended type.
0.5 mm. to - 360 mm. in Adjustable type design.
Approx. Rs 33,000 / Set
Surface Quality & Wear Resistance
We are engaged in offering our clients with a qualitative range of Slip Gauges (Gauge Blocks). These are manufactured using both tungsten carbide and steel as well as loose slip and special slips that comply with IS, BS, DIN, JIS, and other specifications along with mike check sets and wear protector sets. Our range is also certified for excellent calibration and traceability and is available in combinations such as M32, M41, M88, M103 and M112 slips. The surface finish of Master Metrology Gauges is always maintained below 0.2 of 1 Micro-inch. This is the most achievable parameter.
These gauges are made with accuracies to meet any required standards including IS:2984/BS:4311/DIN:861 and American Standard CCC/C/15C.
We also offer these in various grades such as Grade II, Grade I, Grade 0, Grade K and Grade 00.
Approx. Rs 3,300 / Set
Master metrology manufactures pin gauges (Measuring Pins) in various sized and tolerances.
Material: Pin Gauges are manufactured in Steel and Tungsten Carbide.
These are manufactured from dia. 0.8 mm to 16 mm. in increments (steps) of 0.001 mm., 0.01 mm., 0.05 mm., and 0. 1 mm. and 0.5 mm.etc. Steel pins are manufactured from dia. 0.2 mm. to 20 mm. We are manufacturing them as per customer requirement.
Handles & Knobs:
Pins have reversible type (twin headed) handles. Pin sizes can be attached to both sides to make your own plug gauge. Single pins are having Aluminum anodized knobs with their sizes marked on the top face.
Pin gauges have tolerance of +0.002 mm. or ± 0.001 mm.
Diameter of Pin gauge sets are from 0.5 mm. to 20 mm. with various increments.
Pin Holding Cases:
Individual pins are supplied in a plastic case. Pin gauge sets are supplied in an attractive melamine coated wooden case for long life and easy storage.
Any size between 0.2 to 30mm
Pin gauges are manufactured out of following
Approx. Rs 560 / Piece(s)
Master metrology manufactures master setting rings in steel as well as tungsten carbide material.
1 mm. To 300 mm
5 mm. To 60mm
Used for setting any type of internal or external measuring instruments such as bore gauges etc.
Made from oil hardening non shrinking gauge steel, hardened and tempered to 60-62 hrc.
Sub-zero treated at -800 c for dimensional stability.
Actual dimensions duly etched.
Calibrated at 200 c under standards room conditions.
Certificate of calibration is provided along with each master traceable to national length standards.
Morse taper ring gauges & ISO taper ring gauges are also manufactured.
Approx. Rs 900 / Piece(s)
Precision ground threaded pegs or locators are used on CMM machines to measure inter distance bewnt threaded holes. The bottom end of the peg is threaded ti accomodate in the component and the top portion is precision ground to a 2 micron accuracy.
Approx. Rs 960 / Piece(s)
Juo Plugs are used on CMM (Coordinate Measuring Machines) as hole locators to accurately gauge the interdistance between two threads.
Approx. Rs 3,000 / Piece
Outer Dia of components needs to be concentric with the Inner Diameter within a specified limit. In such gauges we maintain the ID and the Pin OD of the gauge in a limit such that only OK components will pass through the gauge.
Approx. Rs 850 / Piece
We are a leading manufacturer and supplier of a wide array of Limit Gauges. The offered range helps in checking a single distance, length or diameter or may serve the inspection of multiple dimensions. Superior quality material that is sourced from most trusted vendors of market is used in the production process. To cater to the diverse requirements of our esteemed customers.
Approx. Rs 4,500 / Piece
We hold expertise in offering a superior quality range of Master Gauges. All the products offered by using qualitative raw material, as par the industry set quality parameters. To ensure that all the products are quality assured in nature, our quality controller team examine all the products on varied quality parameters. We offer this range of products in varied custom-designed models to meet variegated requirements of our clients.
Approx. Rs 4,800 / Piece
Components need to be checked for angularity while maintaining face squareness at the seat there such gauges are used.
We will contact you soon !
Narhe Industrial Area, Pune,